CV9 Master Catalog

1 Specifications subject to change without notice or incurring obligation Pancake ® Cylinders 1.22 Option Specifications 1/2" (5) Bore Also See Page 1.21 Suffix Option -F, -F1, -F2 Threaded Nose Mount (See info page 1.13) Available on Original Series with Actions -XDR, -ODR. For Rod End only use -F For Cap End only use -F1 For Both Ends use -F2 1.31 .75 .75 1.50 1.13 .56 .63 .38 .20 Dia. .50 Dia. .09 Part No: BRK-201 5/8 .25 .72 1/2-20 Nut . Part No. MC-500-195 is included. Material: Brass Accessory Nose Mounting Brackets Order separately – Material Plated Steel .13 .38 .13 + Stroke .38+ B 1.13 1/2-20 Pilot Dia. = .495 .491 Pilot Length = .06 Suffix Option -K Nonrotating, Double Acting Available on Original Series with Actions: -XDR, -ODR. Rotational Tolerance with Piston Rod Fully Retracted (Clamp near Body) is ±1°. Cylinder is not intended to carry any rota- tional load. 90 ° Ref. 61 ° A – J .48 + B K – M .38 + B .38 .25 .56 .88 Standard Rod End Brass Clamp Ground Tool Steel Pin is Guided by Precision Hole in End Cap Clearance in Body for Guide Pin .13 .50 .13 + Stroke V Q N C1–C7 BF BR BFR 06 -XDR ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ -ODR ✓ ✓ ✓ ✓ NA ✓ NA ✓ The Suffix Options charted on the right are available on Original Series with the Actions indicated ( ✓ ). They require no dimensional changes from the Standard Specifications on page 1.21. – Also see Option Information on pages 1.7 thru 1.15. Suffix Option -NR Nonrotating, Single Acting Available on Original Series with Action -ODR Also see Option Information on page 1.8. .25 Hex Stainless Steel Piston Rod Suffix Option -MR, -MR1, -MR2 Male Rod Thread Available on Original Series with Actions -XDR, -ODR. For Rod End only use –MR For Cap End only use –MR1 For Both Ends use –MR2 Also see Option Information on Page 1.8 8-32 x .50 Prefix Option -M Metric Cylinder & Rod Thread, 12.7mm Bore Available on Original Series with Actions: -XDR, -ODR Also see Option Information on page 1.7. 22.2mm Bolt Circle M5 Ports with 9.5mm Dia. Spotface M4 x 12.7 Standard Female Rod Thread M4. Male Rod Thread Option -MR shown. Mounting Holes 3.6mm Diameter Thru 5.9mm C'Bore x 3.6mm Dp. 2 Places for M3 SHCS Except Strokes H-M which have two M4 x 12.0mm Dp. Tapped Mounting Holes on each end. Thread Pitches M3 = 0.5mm M4 = 0.7mm M5 = 0.8mm Conversion Factor Inches x 25.4 = mm Stroke mm 1.6 3.2 6.4 9.5 12.7 15.9 19.1 25.4 31.8 38.1 50.8 76.2 101.6 Stroke Letter A B C D E F G H I J K L M 1.80 .99 .75 1.50 1.13 .56 .20 Dia. .09 .25 .50 Dia. Part No: BRK-202 4-22-04

RkJQdWJsaXNoZXIy NDI5NDE=