Linear Slides

Page 26 Specifications subject to change without notice or incurring obligations Step 1: Basic Slide Model SE500 – 5.0 (– ) – MS1T1 – VZ Stroke 1-8-99 Model Size Toolbar Configurations Integral Option Codes Step 1 Select a slide model size, stroke length, mounting style, plus any optional toolbar, attachment (B1), or integral options (such as Viton seals). Helpful hint: The model size = guide shaft diameter in 3 decimal places. – Order Guide Integral Options ▼ ▼ ▼ Optional Tandem Cylinder Stroke Leave Blank If No Integral Options Are Desired Optional toolbars T1, T3, & T4 may be substituted for standard toolbars at no additional cost. All like models of SE Slides (except SE500) can be joined together for 2-axis motion using the standard toolbars. Use Option T3 to join two SE500 models. All “SE” Slides (except SE250) share identical toolbars with their “EZ” Series cousins. Thus an “SE” slide is easily combined with an “EZ” slide for 2-axis motion. “SE” Series Linear Slides Model Size 250 375 500 625 750 1000 1500 Bore 1/2" 3/4" 1-1/8" 1-1/8" 2" 2-1/2" 3-1/4" Guide Shaft Diameter 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/2" Standard Stroke Length 1/2" to 4" by 1/2" increments 1" to 6" by 1" increments 1" to 10" by 1" increments 1" to 10" by 1" increments 1" to 6" by 1" increments 8" to 18" by 2" increments 1" to 6" by 1" increments 8" to 20" by 2" increments 2" to 30" by 2" increments D – Dowel Hole/Slot Code & Location(s) Available on any or all of the 5 mounting surfaces shown in blue on page 30. Example: D13 specifies dowel hole/slot on bottom surface of bearing block (Surface #1) and on top surface of toolbar (Surface #3). H – Hydraulic Cylinder Seals (150 psi max.) V – Viton Cylinder Seals Bearing Options Sleeve bearings can be substituted for standard linear ball bearings. W – Rulon ® Shaft Bearings X – Duralon ® Shaft Bearings Guide Shaft Options Y – Hollow Guide Shafts Case hardened & ground #52100 tubular steel available on SE750 Models and larger. Z – Stainless Steel Guide Shafts: shaft material compatible with bearing type will be provided. Bearing Type Shaft Material Std. linear ball brgs. 440C hardened & ground SS Option "W" Rulon ® sleeve Hard chrome plated SS Option "X" Duralon ® sleeve Hard chrome plated SS S – Grease fittings, Side T – Grease fittings, Top Model Number Will End Here If No Options Are Desired Ordering example: SE750 – 5.0 – 2.0 – MS1 – J72 ■ Sensor locations – use “ M ” in the Box ( ) if mid-position sensor is required (3 sensors). Note: “ M ” (mid-position) is not available with “ S50, S51, S60 ” sensors. All sensors are located on the primary cylinder, which also contains the magnetic piston band for “ E ” & “ J ” options. Shock options “ D, E & F ” are not available on tandem units. 3-Position Tandem Cylinder Slides Secondary Cylinder Stroke Primary Cylinder Stroke (Not available on SE250 or SE375) Note: See pages 28 & 29 for principle of operation M Series Allen Bolts attach the vertical motion unit to the mounting bar of the horizontal motion unit. T3 or T4 horizontal motion toolbar with special mounting holes is available for joining dissimilar models. – MS1 Standard Mounting Includes: • Tapped mounting holes • Thru mounting holes • Side tapped mounting holes Base Mounting Bar Option Thru Hole Mounting and Tapped Mounting Holes on opposite side Side Tapped Mounting Holes 4 Each Side – MS1B1 Optional Base Mounting Bars Mounting Style & Optional Toolbars Toolbar Option Codes – T1 = Blank Toolbar (no mounting holes). For joining dissimilar models, specify the horizontal toolbar. Horizontal Slide Vertical Slide – T3 for SE500 SE500 or EZ500 – T4 for SE1000 SE500, EZ500, SE750, or EZ750 To order: Add “Option Code” to Mounting Style. Example: SE1000 – 10.0 – MS1 T4

RkJQdWJsaXNoZXIy NDI5NDE=