Linear Slides

Page 60 “EZP” Series Pick & Place Units Specifications subject to change without notice or incurring obligations Max Operating Pressure: 150 psi Output Force: Pounds = Pressure x Power Factor Speed: Speeds up to 24 inches per second are obtainable by utilizing an optional stop package in conjunction with urethane bumpers or hydraulic shocks. Moderate reciprocating loads can be safely cycled up to 12 inches per second by uti- lizing an adjustable stop option without bumpers or shocks. Except for light loads and moderate speeds, operating EZP Pick & Place units without an adjustable stop option is not recommended. Moderate to heavy loads should not be stopped by bottoming the piston against the end cap. Important note: Most failures are caused by severe, damaging impact loads (which act like a Load Sizing VERTICAL MOTION Compact “TS” Style slide (shown with “V04” adjustable downstop) Toolbar Clear anodized aluminum, machined bottom & front for squareness. Bottom mounting surface features 4 tapped mounting holes, plus c’bores at top for thru hole mounting. Front face has 2 tapped mounting holes. Optional slip fit dowel hole and slot (bottom surface only) assure repeatably precise tooling attachments. Code – T1: Optional blank toolbar (no mounting holes) Optional Dowel Hole/Slot Code –D Optional slip fit dowel holes and slip fit dowel slots allow for repeatably precise slide mounting and/or attachment of end tooling. Option may be specified at any of the four surface locations (1, 2, 4 or 6) listed here. #1 – MH1/MH2 end cap mounting surface (bottom mounting surface) #2 – Toolbar bottom #4 – MV1/MV2 end cap mounting surface (side mounting surface) #6 – MF1/MF2/MF3 end cap mounting surface (flange face) Cylinder Endcaps Clear anodized aluminum with precision machined mounting surface Choice of endcap mounting styles Code – MH1: Thru- hole mounting (shown) Code – MH2: Bottom tapped mounting hole Code – MF1/MF2/MF3: Flange mount styles Code – MV1/MV2: Side tapped hole mounting HORIZONTAL MOTION Same component parts as an EZ500 slide. (shown with “H01” adjustable stops) Note: Each axis is designated horizontal or vertical as shown. However, unit can be mounted in any attitude required by your application “H01” Adjustable stops EZP5025 Standard Strokes 1” – 10” ➡ ➡ Std. Strokes 1” – 5” ➡ ➡ 1.0 1.6 3.0 3.0 3.0 8 1.0 1.4 1.4 1.4 1.4 10 Horizontal Stroke 1.0 1.6 3.8 4.0 4.0 7 1.0 1.6 3.8 8.7 9.9 4 1.0 1.6 1.8 1.8 1.8 9 1.0 1.6 3.8 8.7 9.9 2 1.0 1.6 3.8 8.7 9.9 1 1.0 1.6 3.8 8.7 9.9 3 1.0 1.6 3.8 6.0 6.0 6 1.0 1.6 3.8 8.0 8.0 5 5 4 3 2 1 S A F E L O A D S (lbs. ) Vertical Stroke Guide Shaft Diameter Bore Power Factor Extend Power Factor Retract Standard Strokes (Specials available) Ship weight, lbs. Zero stroke Add per inch of stroke Horizontal Vertical 1/2” 1/4” 1-1/8” 1-1/8” .99 .90 .88 .90 1” thru 10” 1” thru 5” by 1” incr. by 1” incr. 3.62 .32 .12 EZP5025 Specifications Engineering Data ➡➡➡ 1-26-99

RkJQdWJsaXNoZXIy NDI5NDE=