Linear Slides

Page 61 Specifications subject to change without notice or incurring obligations “slide hammer” on the piston rod). Proper model sizing, use of adjustable stops and/or shocks/ bumpers, and operating the unit at the lowest possible air pressure will insure successful op- eration and long product life. Accuracy: EZP Pick & Place units feature lin- ear ball bearings for near play free operation. Each bearing has .0005” max “play” or less. The built-in air cylinder will stroke +.015” / –.000” of nominal stroke. Stroke repeatability is ±.001”. Guide shaft straightness tolerance is .0015” per foot of shaft. Bearings in the EZP Pick & Place units are housed in the cylinder end caps. As the stroke increases, the pairs of bearings become spaced further apart, increasing bearing load capacity. Guides built tough with the most advanced features and options EZP7550 Toolbar Clear anodized aluminum, machined bottom and front for squareness. Bottom mounting surface has 2 tapped mounting holes. Front face has 2 tapped mounting holes. Optional slip fit dowel hole and slot (available on front and/or bottom mounting surfaces) assure repeatably precise tooling attachments. Code – T1: Optional blank toolbar (no mtg holes) HORIZONTAL MOTION Same component parts as an EZ750 slide. (shown with “H01” adjustable stops) VERTICAL MOTION Same component parts as an EZ500 slide. (shown with “V01” adjustable stops) Optional Dowel Hole/Slot Code –D Optional slip fit dowel holes and slip fit dowel slots allow for repeatably precise slide mounting and/or attachment of end tooling. Option may be specified at any of the five surface locations (1, 2, 3, 4 or 6) listed here. #1 – MH1/MH2 end cap mounting surface (bottom mounting surface) #2 – Toolbar bottom #3 – Toolbar front face #4 – MV1/MV2 end cap mounting surface (side mounting surface) #6 – MF1/MF2/MF3 end cap mounting surface (flange face) Cylinder Endcaps Clear anodized aluminum with precision machined mounting surface Choice of endcap mounting styles Code – MH1: Thru-hole mounting (shown) Code – MH2: Bottom tapped mounting hole Code – MF1/MF2/MF3: Flange mount styles Code – MV1/MV2: Side tapped hole mounting “V01” Adjustable stops “H01” Adjustable stops Standard Strokes 1” – 18” ➡ ➡ Std. Strokes 1” – 10” ➡ ➡ 1.4 1.8 3.0 4.0 6.0 8.0 8.0 8.0 8.0 8.0 10 1.4 1.8 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 16 1.4 1.8 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 14 Horizontal Stroke 1.4 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 18 1.4 1.8 3.0 4.0 6.0 8.0 12.0 12.0 12.0 12.0 8 1.4 1.8 3.0 4.0 6.0 8.0 12.0 24.0 44.0 56.0 4 1.4 1.8 3.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 12 1.4 1.8 3.0 4.0 6.0 8.0 12.0 24.0 44.0 84.0 2 1.4 1.8 3.0 4.0 6.0 8.0 12.0 24.0 44.0 84.0 1 1.4 1.8 3.0 4.0 6.0 8.0 12.0 24.0 44.0 60.0 3 1.4 1.8 3.0 4.0 6.0 8.0 12.0 20.0 20.0 20.0 6 1.4 1.8 3.0 4.0 6.0 8.0 12.0 24.0 28.0 28.0 5 S A F E L O A D S (lbs. ) Vertical Stroke 10 9 8 7 6 5 4 3 2 1 Guide Shaft Diameter Bore Power Factor Extend Power Factor Retract Standard Strokes (Specials available) Ship weight, lbs. Zero stroke Add per inch of stroke Horizontal Vertical 3/4” 1/2” 2” 1-1/8” 3.14 .99 2.84 .88 1” to 6” by 1” 1” thru 10” 8” to 18” by 2” by 1” incr. 9.98 .74 .32 EZP7550 Specifications ➡➡➡ 1-26-99

RkJQdWJsaXNoZXIy NDI5NDE=